Flashlights > Fenix
Part#: LD01
The Fenix LD01 is extremely small and not much bigger than the AAA cell it uses. It has three modes: Medium -> Low -> High. These modes allow the user to select the best light output and runtime for any given task. The Fenix LD01 uses just one common AAA battery and thanks to its small size and weight, it is perfect for Every Day Carry (EDC). Moreover, its solid reliability has been tested and proven.
Features Cree Q5 7090 XR-E LED Three output modes: 27 Lumens (3.5hrs) -> 10 Lumens (8.5hrs) -> 80 Lumens (1hrs) Four days of survival use (two continuous hours per day on the lowest setting) Uses one 1.5V AAA battery (not included), inexpensive and widely available 7.35cm (L) x 1.4cm (D) | 2.9 in (L) x 0.6 in (D) 14.8-gram (or 0.5 oz) weight (excluding batteries) Made of aircraft-grade aluminum Durable Type III hard-anodized finish Toughened ultra-clear glass lens with AR coating Waterproof to IPX-8 Standards Capable of standing up securely on a flat surface to serve as a candle Reliable twist-switch Includes a spare o-ring, a split ring, and a pocket clip Operation Turn the head of the flashlight clockwise to turn on the flashlight. A counter-clockwise turn will then switch it off. To switch between output modes, turn the light on, then off and within 1.5 seconds after turning the light off, turn it on again and it will switch to the next output mode. Repeat this process to continue switching through the modes. If the light is turned off for over 1.5 seconds, the circuit will be reset and the light will default to its primary mode the next time it is turned on. Mode Sequence: Med, Low and High Batteries not included |
Part#: LD10
The Fenix LD10 is digitally regulated and digitally controlled. It runs on a standard AA battery and has two output modes which produce a total of six levels of output. These modes not only allow the user to select the best output and runtime for any given task, but they also help to aid in an emergency. The LD10 does all this and still retains a very compact size. If you're looking for solid reliability, digitally-regulated brightness, and compact size, this Fenix is for you.
Features Cree 7090 XR-E LED Two modes of output, selected by turning the bezel: General Mode: 9 lumens (34hrs) -> 47 lumens (6hrs) -> 94 lumens (2.2hrs) -> SOS Turbo Mode: 120 lumens (1.5hrs) -> Strobe 17 days of survival use (2 continuous hours per day on the lowest setting) Digitally regulated for constant brightness Uses one 1.5V AA ( Alkaline, NiMH, Lithium ) battery (not included), inexpensive and widely available 100mm (L) x 21.5mm (D) Made of T6 aircraft-grade aluminum Durable Type III hard-anodized finish 50-gram (or 1.7 oz) weight (excluding batteries) Water-proof to IPX8 standard Toughened ultra clear glass lens with AR coating Push-button tail cap switch Capable of standing up securely on a flat surface to serve as a candle Includes a holster, a lanyard, two spare o-rings, and a rubber switch boot This product comes with a textured reflector Operation Press the tailcap button until you hear a click to turn the light on and turn the bezel to select the mode. A fully-tightened head will select Turbo Mode (highest output), and a loosened head will select General Mode. Soft-pressing the tailcap button while the light is on will change the output level of the selected mode. Turn the light off for over two seconds and the circuit will reset. Batteries not included |
Part#: LD20
$59.99 each
The Fenix LD20 is digitally regulated and digitally controlled. It runs on two standard AA batteries and has two output modes which produce a total of six levels of output, max output is 180 lumen. These modes not only allow the user to select the best output and runtime for any given task, but they also help to aid in an emergency. The LD20 does all this and still retains a very compact size. If you're looking for solid reliability, digitally-regulated brightness, and compact size, this Fenix is for you.
Features Utilizes a Premium (Q5) Cree 7090 XR-E LED with a life of 50,000 hours Two modes of output, selected by turning the bezel (patented) General Mode: 9 lumens (71hrs) -> 47 lumens (13hrs) -> 94 lumens (5hrs) -> SOS Turbo Mode: 180 lumens (2hrs) -> Strobe 36 days of survival use (2 continuous hours per day on the lowest setting) Digitally Regulated for Constant Brightness Uses two 1.5V AA ( Alkaline, NiMH, Lithium ) batteries (not included), inexpensive and widely available 150mm (L) x 21.5 mm (D) Made of T6 aircraft grade aluminum Durable Type III hard anodized finish 56-gram (or 2.0 oz) weight (excluding batteries) Waterproof to IPX-8 Standards Toughened ultra clear glass lens with AR coating Push-button tail cap switch Capable of standing up securely on a flat surface to serve as a candle Batteries not included Includes a holster, a lanyard, two spare o-rings, and a rubber switch boot This product comes with a textured reflector Operation Press the tailcap button until you hear a click to turn the light on and turn the bezel to select the mode. A fully-tightened head will select Turbo Mode (highest output), and a loosened head will select General Mode. Soft-pressing the tailcap button while the light is on will change the output level of the selected mode. Turn the light off for over two seconds and the circuit will reset. Two modes with Turbo/Strobe and High/Med/Low/SOS Batteries not included |
Part#: PD20
The Fenix PD20 is digitally regulated and digitally controlled. It runs on one standard CR123A battery and has two output modes which produce a total of six levels of output, max output is 190 lumen. These modes not only allow the user to select the best output and runtime for any given task, but they also help to aid in an emergency. The PD20 does all this and still retains a very compact size. If you're looking for solid reliability, digitally-regulated brightness, and compact size, this Fenix is for you.
Features Cree XP-E LED (R2) with lifespan of 50,000 hours Two modes of output general/turbo - modes selected by turning the bezel: -Turbo Mode: 190 lumens (1 hr) -> Strobe -General Mode: 9 lumens (35 hrs) > 48 lumens (7 hrs) > 96 lumens (2.8 hrs) > SOS Max beam length: 135 meters Digitally regulated output - maintains constant brightness Powered by one 3V CR123A lithium batteries 78.5mm (Length) x 21.5mm (Diameter) 39-gram weight (excluding batteries) Made of durable aircraft-grade aluminum Premium Type III hard-anodized anti-abrasive finish Waterproof to IPX-8 Standard Toughened ultra-clear glass lens with anti-reflective coating Push-button tail cap switch Capable of standing up securely on a flat surface to serve as a candle Anti-roll, slip-resistant body design Included accessories: lanyard, two spare o-rings, body clip, and a rubber switch boot This product comes with a textured reflector Operation Press the tailcap button until you hear a click to turn the light on and turn the bezel to select the mode. A fully-tightened head will select Turbo Mode (highest output), and a loosened head will select General Mode. Soft-pressing the tailcap button while the light is on will change the output level of the selected mode. Turn the light off for over two seconds and the circuit will reset. Batteries not included |
Part#: PD30
The Fenix PD30 is digitally regulated and digitally controlled. It runs on two standard CR123A batteries and has two output modes which produce a total of six levels of output, max output is 235 lumen. These modes not only allow the user to select the best output and runtime for any given task, but they also help to aid in an emergency. The PD30 does all this and still retains a very compact size. If you're looking for solid reliability, digitally-regulated brightness, and compact size, this Fenix is for you.
Features Utilizes a Premium (R2) Cree 7090 XP-E LED with a life of 50,000 hours Two modes of output, selected by turning the bezel General Mode: 9 lumens (65hrs) -> 70 lumens (8hrs) -> 117 lumens (4hrs) -> SOS Turbo Mode: 235 lumens (1.5hrs) -> Strobe 33 days of survival use (2 continuous hours per day on the lowest setting) Digitally Regulated for Constant Brightness Low Uses two CR123A battery (not included) 118mm (L) x 21.5mm (D) Made of aircraft grade aluminum Durable Type III hard anodized finish 49g (or 1.7 oz) weight (excluding batteries) Waterproof to IPX-8 Standard Toughened ultra clear glass lens with AR coating Push-button tailcap switch Capable of standing up securely on a flat surface to serve as a candle Includes a holster, a lanyard, two spare o-rings, and a rubber switch boot. This product comes with a textured reflector Operation Press the tailcap button until you hear a click to turn the light on and turn the bezel to select the mode. A fully-tightened head will select Turbo Mode (highest output), and a loosened head will select General Mode. Soft-pressing the tailcap button while the light is on will change the output level of the selected mode. Turn the light off for over two seconds and the circuit will reset. Batteries not included |
Part#: TK12
$74.99 each
The Fenix TK12 follows Fenix's philosophy of designing innovative flashlights with a focus on ergonomic design. The TK12 offers three modes of output - Outdoor, Camping, and Hunting modes. It features an intelligent memory circuit that will default to the last used mode when you turn it on. With its 240 lumen max output and 200 meter illumination distance, the TK12 is the perfect flashlight for outdoor adventures.
Features: Cree XR-E LED (R2) with lifespan of 50,000 hours Three modes, two types of output for each mode, selected by turning the bezel (Patented) - Outdoor mode: (A) 50 lumens/12 hrs, (B) 225 lumens/1.5 hrs - Camping mode: (A) 5 lumens/120 hrs, (B) 90 lumens/5.5 hrs - Hunting mode: (A) Strobe/3 hrs, (B) 225 lumens/1.5hrs OP textured reflector, throws beam over 200 meters Dual switch system with easy operation - one for on/off, the other for output adjustment Digitally regulated output - maintains constant brightness Intelligent memory function Anti-reverse connection circuit Uses two 3v CR123A lithium batteries Dimensions: 137.5mm (Length) x 25.4mm (Diameter) x 34mm (Head) Made of durable aircraft-grade aluminum Premium Type III hard-anodized anti-abrasive finish Weight: 119g (not including batteries) Waterproof to IPX-8 standard Toughened ultra-clear glass lens with anti-reflective coating Tactical tail cap switch with momentary-on function Anti-roll, slip-resistant body design Included accessories: holster, lanyard, body c lip, two spare o-rings, and rubber switch boot Batteries not included |
Part#: TK11
The Fenix Tactical series (T) features a powerful, solid, durable, and waterproof design intended for rugged outdoor and military use, it’s as solid as a tank. The TK11 can use either two CR123A batteries or one 18650 battery with a protective circuit, and it maintains excellent constant brightness with two output modes: General mode, which can last for a whole night and can be used for general illumination, and Turbo mode, which can be used whenever high-powered light is needed – search and rescue, long-range target identification, etc.
Features: Cree Premium (R2) 7090 XR-E LED with lifespan of 50,000 hours Two modes of output, selected by turning the bezel: Turbo Mode: Constant 240 Lumens, 2.7 hours, then 50% output (18650 Li-ion) ¨ General Mode: Constant 64 Lumens, 12 hours (18650 Li-ion) Highly efficient focused head - throws beam over 200 meters Smooth reflector for maximum throw distance Digitally regulated output - maintains constant brightness Low battery indication system Uses either two 3V CR123A lithium batteries or one 18650 Li-ion* *Note: Only 18650s with protective circuits can be used, batteries not included Durable aircraft-grade aluminum housing 135mm (length) x 34mm (diameter) 136 gram weight (excluding batteries) Premium Type III hard-anodized anti-abrasive finish Waterproof to IPX-8 Standard Tactical grip ring for Cigar technique (removable) Toughened ultra-clear glass lens with anti-reflective coating Tactical tailcap switch with momentary-on function Slip-resistant body design Batteries not included |
Part#: TK30
$139.99 each
The Fenix TK30 flashlight utilizes a Cree MC-E Quad LED, and delivers an amazing 630 lumens of brightness powered by four CR123A batteries or two 18650 rechargeable batteries (with included extension tube. Max runtime can be up to 90 hours on low. The Fenix TK30 would be a good choice for Search and Rescue and other first responders that need extremely bright light in a small package.
Features: Cree MC-E LED with a 50,000 hour lifespan Uses two CR123A batterys or one 18650 rechargeable battery Uses four CR123A batterys or two 18650 rechargeable batteries (with extension tube) Three sets of modes, two types of output for each mode, selected by turning the bezel Performance using two CR123A batteries (runtimes longer with one 18650 rechargeable battery) Searching Mode: Output A - 100 Lumens / 5 Hours Output B - 370 Lumens / 1 Hours Camping Mode: Output A - 12 Lumens / 30 Hours Output B - 175 Lumens / 2.7 Hours Hunting Mode: Output A - Strobe / 2 Hours Output B - 370 Lumens / 1 Hours Performance using two 2500 mAh 18650 rechargeable batteries (with extension tube) Searching Mode: Output A - 100 Lumens / 16 Hours Output B - 630 Lumens / 1.5 Hours Camping Mode: Output A - 12 Lumens / 90 Hours Output B - 175 Lumens / 8.4 Hours Hunting Mode: Output A - Strobe / 3 Hours Output B - 630 Lumens / 1.5 Hours Max beam length: 225 meters / 300 meters (with extension tube) Digitally regulated for constant output Intelliegent memory function Working voltage: 3V~12V Weight - 183g (excluding batteries) / 215g (excluding batteries, with extension tube) Dimensions - 208mm (L) x 39.4mm (D) Made of aircraft-grade aluminum Durable Type-III hard-anodized finish Waterproof to IPX-8 standard Toughened ultra-clear glass lens with anti-reflective coating Tactical tailcap switch with momentary-on function Included accessories: lanyard, extension tube, a battery positive connector, two spare o-rings, and a rubber switch boot. Batteries not included |
Part#: TK40
The Fenix TK40 is the latest addition to the TK-Series and is the first Fenix to use Cree's MC-E quad-die, a very powerful LED producing up to 630 lumens. Powered by eight AA batteries the TK40 is the world's brightest, AA-powered flashlight. Its optimized reflector enables it to throw a wall of light for over 300 meters. The TK40 has two different modes of output, each with four different levels - a total of eight different outputs with intelligent circuitry that will memorize your last-used primary mode.
Features Cree MC-E LED with a 50,000 hour lifespan 2 Modes, 8 Total Outputs Primary Modes (in order) Turbo - 630 Lumens, 1 Hour Low - 13 Lumens, 130 Hours Medium - 93 Lumens, 11 Hours High - 277 Lumens, 4.5 Hours Strobe Modes (in order) Strobe Slow Flash SOS Fast Flash Digitally regulated for constant output Powered by eight 1.5V AA batteries - Alkaline or Ni-MH Do not use Energizer Lithium AA cells for this light.Can operate off just four AA during an emergency Dimensions - 208mm (L) x 39.4mm (D) Weight - 284g (excluding batteries) Crafted from T6 aircraft-grade aluminum Type-III hard-anodized finish Waterproof to IPX-8 standard Toughened ultra-clear glass lens with anti-reflective coating Push-button tailcap switch Stands on end to operate as a candle Batteries not included |
